Omron, H3CR-F Series

Wide power supply ranges of High Voltage 100 to 240 VAC/100 to 125 VDC and Low Voltage 24 to 48 VAC/12 to 48 VDC.
ON- and OFF-times can be set independently and so combinations of long ON- or OFF-time and short OFF- or ON time settings are possible.
Twenty-four time ranges from 0.05 s to 300 h depending on the model to be used.
Models with a flicker ON start or flicker OFF start are available.
Easy sequence checks through instantaneous outputs for a zero set value at any time range.
Length, when panel-mounted with a Socket, of 80 mm or less.
11-pin and 8-pin models are available.

last update: June 27, 2014

General

Item	H3CR-F	H3CR-F8	H3CR-FN	H3CR-F8N
Operating mode	Flicker OFF start		Flicker ON start
Pin type	11-pin	8-pin	11-pin	8-pin
Operating/Reset method	Time-limit operation/Time-limit reset or self-reset
Output type	Relay output (DPDT)
Mounting method	DIN track mounting, surface mounting, and flush mounting
Approved standards	UL508, CSA C22.2 No.14, NK, Lloyds, CCC Conforms to EN61812-1 and IEC60664-1 (VDE0110) 4kV/2. Output category according to EN60947-5-1.

Note: For details, refer to your OMRON website.

Time Ranges

Time unit		s (sec)	×10 s (10 sec)	min (min)	×10 min (10 min)	h (hrs)	×10 h (10 hrs)
Fullscale setting	1.2	0.05 to 1.2	1.2 to 12	0.12 to 1.2	1.2 to 12	0.12 to 1.2	1.2 to 12
	3	0.3 to 3	3 to 30	0.3 to 3	3 to 30	0.3 to 3	3 to 30
	12	1.2 to 12	12 to 120	1.2 to 12	12 to 120	1.2 to 12	12 to 120
	30	3 to 30	30 to 300	3 to 30	30 to 300	3 to 30	30 to 300

Note: The times that can be set are given. When the time setting knob is turned below “0” until the point where the time setting knob stops, the output will operate instantaneously at all time range settings. For details, refer to your OMRON website.

Ratings

*Rated supply voltage 1 2 3**	• 100 to 240 VAC 50/60 Hz/100 to 125 VDC • 24 to 48 VAC 50/60 Hz/12 to 48 VDC
Operating voltage range	85% to 110% of rated supply voltage; 90% to 110% with 12-VDC models
Power reset	Minimum power-opening time: 0.1 s
Power consumption	100 to 240 VAC: approx. 10 VA (2.1 W) at 240 VAC 24 VAC/VDC: approx. 2 VA (1.7 W) at 24 VAC, approx. 1 W at 24 VDC
Control outputs	Contact output: 5 A at 250 VAC/30 VDC, resistive load (cosφ = 1) The minimum applicable load is 10mA at 5VDC (P reference value). Contact materials: Ag-alloy

*1. A power supply with a ripple of 20% max. (single-phase power supply with full-wave rectification) can be used with each DC Model.
*2. Do not use an inverter output as the power supply. Refer to your OMRON website for details.
*3. Refer to your OMRON website when using the Timer together with a 2-wire AC proximity sensor.

Characteristics

Accuracy of operating time	±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 1.2 and 3 s)
Setting error	±5% FS ±50 ms max.
Reset time	0.1 s max.
Reset voltage	10% max. of rated voltage
Influence of voltage	±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 1.2 and 3 s)
Influence of temperature	±1% FS max. (±1% FS ±10 ms max. in ranges of 1.2 and 3s)
Insulation resistance	100 MΩ min. (at 500 VDC)
Dielectric strength	2,000 VAC, 50/60 Hz for 1 min (between current-carrying metal parts and exposed non- current-carrying metal parts) 2,000 VAC, 50/60 Hz for 1 min (between control output terminals and operating circuit) 2,000 VAC, 50/60 Hz for 1 min (between contacts of different polarities) 1,000 VAC, 50/60 Hz for 1 min (between contacts not located next to each other)
Impulse withstand voltage	5kV (between power terminals), however, 1kV for 24 to 48VAC, 12 to 48 VDC 5kV (between current-carrying terminal and exposed non-current-carrying metal parts), however 1.5 kV for 24 to 48 VAC, 12 to 48 VDC
Noise immunity	±1.5 kV (between power terminals), square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)
Static immunity	Malfunction: 8 kV Destruction: 15 kV
Vibration resistance	Destruction: 10 to 55 Hz with 0.75-mm single amplitude for 2 hrs each in three directions Malfunction: 10 to 55 Hz with 0.5-mm single amplitude for 10 min each in three directions
Shock resistance	Destruction: 980 m/s² three times each in six directions Malfunction: 98 m/s² three times each in six directions
Ambient temperature	Operating: -10°C to 55°C (with no icing) Storage: -25°C to 65°C (with no icing)
Ambient humidity	Operating: 35% to 85%
Life expectancy	Mechanical: 20 million operations min. (under no load at 1,800 operations/h) Electrical: 100,000 operations min. (5 A at 250 VAC, resistive load at 1,800 operations/h) *
EMC	(EMI) EN61812-1 Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN61812-1 Immunity ESD: IEC61000-4-2 Immunity RF-interference: IEC61000-4-3 Immunity Burst: IEC61000-4-4 Immunity Surge: IEC61000-4-5 Immunity Conducted Disturbance: IEC61000-4-6 Immunity Voltage Dip/Interruption: IEC61000-4-11
Case color	Light Gray (Munsell 5Y7/1)
Degree of protection	IP40 (panel surface)
Weight	Approx. 100 g

Note: Refer to the Life-test Curve (Reference).

Life-test Curve (Reference)

Reference:
A maximum current of 0.15 A can be switched at 125 VDC (cosφ = 1) and a maximum current of 0.1A can be switched at 125V DC and L/R = 7ms.
In both cases, a life of 100,000 operations can be expected.
The minimum applicable load is 10 mA at 5 VDC (failure level: P).

last update: June 27, 2014

H3CR-F
H3CR-FN

H3CR-F8
H3CR-F8N

Flush mounting adapter

Y92F-30 flush mounting adapter (order separately)

Note: 1. The orientation of the Adapters for two or more Timers is different for a horizontal or vertical layout. Make sure
the orientation is correct.
Consecutive Mounting of n Timers
Without Front Covers: N = (48n - 2.5) + 1 - 0
With Front Covers: N = (51n - 5.5) + 1 - 0
With Panel Covers: N = (50n - 4.5) + 1 - 0
2. The applicable thickness of the mounting panel must be 1 to 5 mm.

Y92F-73 flush mounting adapter (order separately)

Note: A Front Cover and Flush Mounting Adapter cannot be used at the same time.
Note: The applicable thickness of the mounting panel must be 1 to 3.2 mm.
* Insert the Timer from the back of the Adapter.

Y92F-74 flush mounting adapter (order separately)

Note: A Front Cover and Flush Mounting Adapter cannot be used at the same time.
Note: The applicable thickness of the mounting panel must be 1 to 3.2 mm.

Dimensions with front connecting socket
P2CF-08-[]/P2CF-11-[]

* These dimensions vary with the kind of DIN track (reference value).

Dimensions with back connecting socket
P3G-08/P3GA-11

Note: There are no restrictions to the mounting direction.

TITLE	DOCUMENT TYPE	SIZE
H3CR	Catalog	6407 KB
Model selection guide for timers	Catalog	2548 KB
H3CR-F Twin timer	Catalog	795 KB
H3CR-F Twin timer	Catalog	728 KB
H3CR-G Star-Delta timer	Catalog	701 KB
H3CR-G Star-Delta timer	Catalog	704 KB
H3CR-H Power off delay timer	Catalog	1077 KB
H3CR-H Power off delay timer	Catalog	742 KB
H3CR-F Twin timer	Catalog	1187 KB
H3CR-G Star-Delta timer	Catalog	1147 KB
H3CR-H Power OFF delay timer	Catalog	1169 KB

General

Time Ranges

Ratings

Characteristics

Life-test Curve (Reference)

H3CR-F
H3CR-FN

H3CR-F8
H3CR-F8N

Flush mounting adapter

Y92F-30 flush mounting adapter (order separately)

Y92F-73 flush mounting adapter (order separately)

Y92F-74 flush mounting adapter (order separately)

Dimensions with front connecting socket
P2CF-08-[]/P2CF-11-[]

Dimensions with back connecting socket
P3G-08/P3GA-11

Group Sites

Our Partner Sites

Subscribe Our Newsletter

General

Time Ranges

Ratings

Characteristics

Life-test Curve (Reference)

H3CR-F H3CR-FN

H3CR-F8 H3CR-F8N

Flush mounting adapter

Y92F-30 flush mounting adapter (order separately)

Y92F-73 flush mounting adapter (order separately)

Y92F-74 flush mounting adapter (order separately)

Dimensions with front connecting socket P2CF-08-[]/P2CF-11-[]

Dimensions with back connecting socket P3G-08/P3GA-11

H3CR-F
H3CR-FN

H3CR-F8
H3CR-F8N

Dimensions with front connecting socket
P2CF-08-[]/P2CF-11-[]

Dimensions with back connecting socket
P3G-08/P3GA-11