• Same shape as OMRON Z Basic Switches except in pin plunger position, yet endures inrush currents as large as 75 A.
• Same shape as OMRON Z Basic Switches except in pin plunger position, yet endures inrush currents as large as 75 A.
Rated voltage (V) |
Non-inductive load (A) | Inductive load (A) | ||||||
---|---|---|---|---|---|---|---|---|
Resistive load |
Lamp load |
Inductive load |
Motor load | |||||
NC | NO | NC | NO | NC | NO | NC | NO | |
125 VAC 250 VAC 500 VAC |
20 20 15 |
7.5 7.5 4 |
20 20 10 |
12.5 8.3 2 |
||||
8 VDC 14 VDC 30 VDC 125 VDC 250 VDC |
20 20 6 0.5 0.25 |
3 3 3 0.5 0.25 |
1.5 1.5 1.5 0.5 0.25 |
20 15 5 0.05 0.03 |
12.5 12.5 5 0.05 0.03 |
|||
Note:Note:
1. The above values are for steady-state current.
2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
5. The ratings values apply under the following test conditions:
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%RH
(3) Operating frequency: 20 operations/min
Operating speed | 0.01 mm to 1m/s * 1 | |
---|---|---|
Operating frequency | Mechanical | 240 operations/min |
Electrical | 20 operations/min | |
Insulation resistance | 100 MΩ min. (at 500 VDC) | |
Contact resistance | 15 mΩ max. (initial value) | |
Dielectric strength |
1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity 2,000 VAC, 50/60 Hz for 1 min between the current-carrying metal parts and the ground, and between each terminal and non-current- carrying metal parts |
|
Vibration resistance | Malfunction | 10 to 55 Hz, 1.5-mm double amplitude * 2 |
Shock resistance | Destruction | 1,000 m/s2 max. |
Malfunction | 300 m/2 max. * 1 * 2 | |
Durability | Mechanical | 1,000,000 operations min. |
Electrical | 500,000 operations min. | |
Degree of protection | IP00 | |
Degree of protection against electric shock | Class I | |
Proof tracking index (PTI) | 175 | |
Ambient operating temperature | -25 ° C to 80 ° C (with no icing) | |
Ambient operating humidity | 35% to 85%RH | |
Weight | Approx. 22 to 58 g |
Note:*1. The value is for the pin plunger. (Contact your OMRON representative for other models.)
*2. Malfunction: 1 ms max.
Contacts | Shape | Rivet |
---|---|---|
Material | Silver alloy | |
Gap (standard value) | 0.5 mm | |
Inrush current | NC | 75 A max. |
NO | 75 A max. |
("-A" is not included in the model numbers.)
Note: 1. Appropriate terminal screw tightening torque: 0.78 to 1.18 Nm.
2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Use M4 mounting screws with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 1.18 to 1.47 Nm.
The Switch can be panel mounted, provided that the hexagonal nut of the actuator is tightened to a torque of 2.94 to 4.9 Nm.
The models, illustrations, and graphics are for screw-terminal models. (The dimensions for models that are omitted here are the same as for pin-plunger models.)
Note: Do not use both M12 mounting screw and mounting holes at the same time.
Note: Do not use both M12 mounting screw and mounting holes at the same time.
Note: Do not use both M12 mounting screw and mounting holes at the same time.
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Soldering Terminal Use (Phenol Resin)
Note: The Cover has five thin, easy-to-separate portions for easy lead wire connections.
Screw Terminal Use (Phenol Resin)
Note: The Cover has six thin, easy-to-separate portions for easy lead wire connections.
Soldering Terminal Use (Metal Press Mold)
Note: The Cover has five holes for easy lead wire connections.
Screw Terminal Use (Metal Press Mold)
Note: The Cover has six holes for easy lead wire connections.
Soldering or Screw Terminal Use (Vinyl Chloride)
Note: Each dimension has a tolerance of ±0.4 mm unless otherwise specified. (±0.8 mm for the AP-Z)
Note: 1. Each dimension has a tolerance of ±0.4 mm unless otherwise specified.
2. The material is EAVTC (Epoxide Alkyd Varnished Tetron Cloth) and its heat-resisting temperature is 130°C.
TITLE | DOCUMENT TYPE | SIZE |
A Series | Catalog | 1694 KB |
---|