Omron, D4CC Series

• New center roller lever models that enable ganged mounting of up to 6 Switches.

• Cable connectors for easy Switch replacement.

• Triple-seal construction to provide IEC IP67 degree of protection.

• Operation indicators available for easy monitoring (standard indicator is lit when Switch is not operating).

• Approved by UL and CSA. (Ask your OMRON representative for Information on approved models.)

Ratings

Rated voltage	Non-inductive load (A)				Inductive load (A)
	Resistive load		Lamp load		Inductive load		Motor load
	NC	NO	NC	NO	NC	NO	NC	NO
125 VAC	1	1	1	0.7	1	1	1	1
30 VDC	1	1	1	1	1	1	1	1

Note: 1. The above current ratings are for steady-state current.
2. Inductive loads have a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp loads have an inrush current of 10 times the steady-state current.
4. Motor loads have an inrush current of 6 times the steady-state current.

D4CC-3, D4CC-4, 1 A at 30 VDC

Inrush current	NC	5 A max.
Inrush current	NO	2.5 A max.

Characteristics

Degree of protection		IP67
*Durability 1**	Mechanical	10,000,000 operations min.
*Durability 1**	Electrical	200,000 operations min. (1 A at 125 VAC, resistive load)
Operating speed		0.1 mm/s to 0.5 m/s (in case of plunger) 1 mm/s to 1 m/s (in case of roller lever)
Operating frequency	Mechanical	120 operations/min
Operating frequency	Electrical	30 operations/min
Rated frequency		50/60 Hz
Insulation resistance		100 MΩ min. (at 500 VDC)
Contact resistance (initial)		100 mΩ max.
Dielectric strength	Between terminals of same polarity	1,000 VAC, 50/60 Hz for 1 min
	Between current-carrying metal parts and ground	1,500 VAC, 50/60 Hz for 1 min
	Between each termi-nal and non- current-carrying metal part	1,500 VAC, 50/60 Hz for 1 min
Vibration resistance	Malfunction	10 to 55 Hz, 1.5-mm double amplitude *2
Shock resistance	Destruction	1,000 m/s² max.
Shock resistance	Malfunction	500 m/s² max. *2
Ambient operating temperature		-10°C to +70°C (with no icing)
Ambient operating humidity		35% to 95%RH
Weight		Approx. 120 g (in the case of D4CC-1002)

Note: The above figures are initial values.
*1. The values are calculated at an operating temperature of +5°C to +35°C,and an operating humidity of 40% to 70%RH. Contact your OMRON sales representative for more detailed information on other operating environments.
*2. Excluding plastic rod models.

Leakage Current for Switches with Indicators

The leakage current and resistance of Switches with indicators are as follows:

Item Model	D4CC-2[][][]	D4CC-4[][][]
Voltage	125 VAC	30 VDC
Leakage current	1.0 mA	1.0 mA
Resistive value	150 k Ω	30 k Ω

last update: May 17, 2017

(Unit: mm)

Switches

Limit Switches

The [] in each model number is replaced with the code expressing the rated load of the model. Refer to Model Number Legend.

Pin Plunger
D4CC-[]001

Roller Plunger
D4CC-[]002

Crossroller Plunger
D4CC-[]003

Roller Lever
D4CC-[]024

Sealed Pin Plunger
D4CC-[]031

Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.

Please click image to enlarge (open in a new window).

Sealed Roller Plunger
D4CC-[]032

Sealed Crossroller Plunger
D4CC-[]033

Plastic Rod
D4CC-[][]50

Center Roller Lever
D4CC-[][]60

Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.

Applicable Cables

Select one of the specified Connector Plugs from the following table.

XS2F-D421-[]80-F (For DC)
XS2F-A421-[]90-F (For AC)

Special Mounting Plates (Limit Switches are not attached to the Plates.)

D4C-P001 (For D4CC-[]001)

D4C-P002 (For D4CC-[]002)

D4C-P020 (For D4CC-[]024)

Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.

Remarks

There is no difference in mounting pitch between the Mounting Plate and the WL/WL-N. The mounting depth of the D4CC with the Mounting Plate attached is, however, shorter than that of the panel-mounted WL/WL-N.

last update: May 17, 2017

TITLE	DOCUMENT TYPE	SIZE
D4CC Series	Catalog	720 KB
D4C(C) Enclosed switch(ENG/JPN)	Catalog	277 KB